Messages

1

Bugs and Issues / Re: Print diagram full page

« on: November 13, 2020, 02:52:49 am »

Hi
I wasn't successful trying Microsoft Print to PDF.
I ended up using PDF Creator and a scaling percentage like 32%. I had to fine-tune the percentage by trial and error. It's a pity there isn't a more direct way to do this.
I had two diagrams to export to PDF and ideally I wanted both on A0 paper format (even though that's not so important in vector PDF). For some reason, one diagram was forced to A4 paper format I have no idea why !

2

General Board / Re: Exported diagram has empty space

« on: September 25, 2020, 06:37:28 pm »

Hello,
Exporting to PDF, I have the same problem on EA 15.1 and data imported from ArcGIS SDE geodatabase. It was exporting correctly and now not anymore. With PDF Creator, it's terrible : 3/4 of the page is empty. It's a bit better with Microsoft print to PDF. I get an empty area on the right just like in PanZupa's 2014 post.
I'm not sure I did any resizing as described by PanZupa in his following thread. For me the problem appeared when we migrated to V15.1

3

Bugs and Issues / Re: Print diagram full page

« on: September 10, 2020, 03:44:45 pm »

OK, I'll try that out and let you know
Thanks.

4

Suggestions and Requests / Re: case insensitive sorting

« on: August 27, 2020, 01:50:10 am »

I don't think it has, but if you want to weigh in on the discussion, make sure to send a feature request to Sparx

Thanks Geert !
Done !

5

Bugs and Issues / Print diagram full page

« on: August 27, 2020, 01:46:31 am »

Hi,
We've just migrated to v15.1, previously on v14.
On v14, I used to be able to print to PDF with my diagram taking up the whole page. Now on v15.1, nothing seems to work.
I've tried diagram properties Page setup as well as print page setup options. The result is always the same.
Using PDF Creator

6

Suggestions and Requests / Re: case insensitive sorting

« on: August 27, 2020, 12:43:04 am »

Hello!
Does anyone know whether this has been implemented?
Cheers,
Timothee

7

PCS General Board / Re: Sort tables in alphabetical order in diagram

« on: August 27, 2020, 12:41:25 am »

Thanks MichaelIJ!
That works, as I am on v15.1.
Most tables are sorted correctly. However there are a few misteries.
The first class is called CLASSEMENT
Then there is a series of classes with names starting with the word JARDINS (JARDINS_ACCES_..., JARDINS_CATEGORIE_..., etc).
Then another series starting with the characters dvMonu_ (dvMonu_Categorie1, dvMonu_Categorie2, ..., dvMonu_ValeurSite, dvMonu_actualite, dvMonu_note)

So here's the list omitting many items which are correctly sorted :

CLASSEMENT
JARDINS_ACCES_ICOMOS
JARDINS_CATEGORIE_ICOMOS
...
dvMonu_Categorie1
dvMonu_Categorie2
...
dvMonu_TypeThematique
dvMonu_ValeurSite
dvMonu_actualite
dvMonu_note

Any idea why
- J comes before d?
- a of actualite comes before C of Categorie or V of ValeurSite.

APPARENTLY, uppercase and lowercase are sorted separately.
Is there any way to configure EA not to do that?
I see I'm not the only one to wish for a case insensitive sorting.
https://sparxsystems.com/forums/smf/index.php?topic=29124.0
Has this been implemented? I haven't found it yet.
Thanks again to all of you!

8

PCS General Board / Re: Sort tables in alphabetical order in diagram

« on: August 26, 2020, 06:15:42 pm »

Hello everyone,
MichaelIJ, your solution number 1 seems ideal.
> Use the "Box" layout found in the "Diagram Layout" panel and select the "Name (ascending)" for the Sort By option
However, I can't find the sort by ascending functionality. Could you tell me where to find it ?
Kind regards,
Timothée

9

PCS General Board / Sort tables in alphabetical order in diagram

« on: August 22, 2020, 03:28:50 am »

I have quite a number of classes listed in the tree and I would like to generate a diagram of these tables sorted alphabetically.
This seems so obvious that I must be missing something. But I have searched the interface all-over